manualshive.com logo in svg

Sharp AR-BC320, Service Manual, Page: 111 / 344

Share
Download
Sharp AR-BC320 Service Manual Download Page 111

AR-BC320  SETTING AND ADJUSTMENTS  8 - 4

7) Apply a digital multi-meter to the connector pins of the high

voltage adjustment harness corresponding to the output mode
to be adjusted.

8) Press the [EXECUTE] key.

The developing bias voltage is outputted for 30sec.

If this operation is performed for a long time, the OPC drum
and the developing roller may be damaged. Be careful to per-
form this operation in a short time.

It is advisable to install an unnecessary developing unit and
unnecessary OPC drums to the machine for this adjustment.

9) Check the monitor voltage with the digital multi-meter.

If the monitor voltage is not in the above specified range,
change the adjustment value and adjust again. If the specified
voltage is not obtained even by changing the adjustment
value, the following parts may be judged as defective.

High voltage PWB

PCU PWB

Developing unit

Photoconductor unit

High voltage circuit electrode

This adjustment must be performed in the following cases:

• When the high voltage power PWB is replaced.

• When a U2 trouble occurs.

• When the PCU PWB is replaced.

• When the EEPROM of the PCU PWB is replaced.

1) Enter the SIM 8-6 mode.

SIM 8-6

2) Select the mode to be adjusted with the color key and scroll

key.

3) Enter the adjustment value (specified value), and press the

[OK] key.

By entering the default value (specified value), the specified
voltage is outputted.

Press the [EXECUTE] key to output the transfer voltage.

The image density sensor sections are of uneven quality in parts
and assembly. This causes variations in the absolute detection
level between machines. This adjustment (calibration) is per-
formed to correct the variations.

This adjustment is required in the following cases:

• When the image density sensor is replaced.

• When the transfer unit is replaced. 

• When maintenance is performed. 

• When U2 trouble occurs.

• When the PCU PWB is replaced.

• When the EEPROM on the PCU PWB is repalced.

The targets of the adjustment are the color image density sensor
and the black image density sensor. There are following adjust-
ment methods:

• Color image density sensor adjustment (adjustment by the

adjustment jig) SIM44-13

• Black image sensity sensor adjustment SIM44-2

• Image density sensor adjustment (The color image density sen-

sor and the black image density sensor are adjusted at the
same time.) (Simple adjustment) SIM44-36

Normally the following adjustments are executed:

• ADJ 2A Color image density sensor adjustment (adjustment by

the adjustment jig) (SIM44-13)

• ADJ 2B Black image density sensor adjustment (SIM44-2)

ADJ 1C

Transfer voltage adjustment

Item

Print mode

Standard setting 

value (Default)

Adjustment 

range

Output voltage (Kv)

K

C

M

Y

K

C

M

Y

A

PLAIN_SPX_CL

Color

Normal paper

117mm/s

173 159 132 132

51 - 255

2.4

2.4

2.4

2.4

B

PLAIN_DPX_CL

Color

Normal paper(Duplex mode)

117mm/s

188 173 142 142

2.7

2.7

2.7

2.7

C

OHP1_CL

Color

Transparency film 1

117mm/s

204 187 153 153

3

3

3

3

D

OHP2_CL

Color

Transparency film 2

58.5mm/s 137 150 153 163

1.7

2.2

3

3.3

E

HEAVY P1_SPX_CL

Color

Thick paper 1

58.5mm/s 158 146 122 122

2.1

2.1

2.1

2.1

F

HEAVY_P1_DPX_CL

Color

Thick paper 1(Duplex mode)

58.5mm/s 188 173 142 142

2.7

2.7

2.7

2.7

G

HEAVY_P2_CL

Color

Thick paper 2

58.5mm/s 173 159 132 132

2.4

2.4

2.4

2.4

H

ENV_CL

Color

Envelope

117mm/s

163 150 125 125

2.2

2.2

2.2

2.2

I

PLAIN_SPX_BW

B & W Normal paper

140mm/s

178

2.5

J

PLAIN_DPX_BW

B & W Normal paper(Duplex mode)

140mm/s

178

2.5

K

OHP1_BW

B & W Transparency film 1

117mm/s

204

3

L

OHP2_BW

B & W Transparency film 2

58.5mm/s 137

1.7

M

HEAVY_P1_SPX_BW

B & W Thick paper 1

58.5mm/s 147

1.9

N

HEAVY_P1_DPX_BW

B & W Thick paper 1(Duplex mode)

58.5mm/s 178

2.5

O

HEAVY_P2_BW

B & W Thick paper 2

58.5mm/s 163

2.2

P

ENV_BW

B & W Envelope

140mm/s

168

2.3

Color

Actual output variable range

Voltage change/Adjustment value (1) (Varying amount when the adjustment value is changed by 1)

K

0 to 4000V

About 19.6V

C

0 to 4500V

About 22.1V

M

0 to 6000V

About 29.4V

Y

0 to 6000V

About 29.4V

ADJ 2

Image density sensor adjustment

Summary of Contents for AR-BC320

























































































































































































































































































































































Reviews:

No comments