manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 61 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 61

Chapter 1 About Ethernet Switches 325 and 425

61

System Configuration Guide

 

Back panel

The back panel of the Ethernet Switch 325-24T is shown in 

Figure 5

. 

Table 4

 

describes the components on the back panel.

Figure 5   

Ethernet Switch 325-24T back panel

Cooling fans

Two cooling fans are located on one side of the Ethernet Switch 325 to provide 
cooling for the internal components. (See 

Figure 2 on page 57

). When you install 

the switch, be sure to allow enough space on both sides of the switch for adequate 
ventilation. For more information on installing the Ethernet Switch 325, see 

Installing the Nortel Ethernet Switch 325

 (217149-B).

T

Green/steady

This port is set to operate at 1000 Mb/s, and 
the link is good.

Amber/steady

Station connected at 10/100 Mb/s.

Off

No link on Copper uplink port.

A

Green/blinking

Indicates activity on link.

Off

No activity on the link.

Table 4   

Components on the Ethernet Switch 325 back panel

Item

Description

1

AC power receptacle

Table 3   

Ethernet Switch 325-24G LED descriptions (continued)

Label

Color/Status

Meaning

100-240 V-
50-60Hz 2A

11110EA

1

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments