manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 409 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 409

409

System Configuration Guide

 

Appendix A
Installing an SFP Transceiver

SFPs are hot-swappable input and output enhancement products that allow 
Gigabit Ethernet ports to link to Short Wavelength (SX), Long Wave length (LX), 
and Coarse Wavelength Division Multiplexed (CWDM) fiber optic networks. 

The Ethernet Switch 425 has two front-panel ports. They are port numbers 25 and 
26 on the Ethernet Switch 425-24T and port numbers 49 and 50 on the Ethernet 
Switch 425-48T.

If you insert an SFP GBIC into one on these ports, that port handles gigabit 
Ethernet speed only. If there are no optional SFPs inserted in to these ports, they 
function at 10/100/1000 Mbps ports.

This appendix describes technical specifications and installation instructions on 
Small Form Factor Pluggable (SFP) transceivers, which includes the includes 
Coarse Wavelength Division Multiplexed (CWDM) SFPs, that are supported by 
the Ethernet Switch 425.

This chapter includes the following topics:

•

“Guidelines” on page 410

•

“Product Description” on page 410

•

“Installing SFPs” on page 414

•

“Technical Specifications” on page 416

•

“How to get help” on page 423

Note: 

The term SFP is used in this chapter to describe features or 

technical specifications of an SFP and a CWDM SFP.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments