Nortel 425-24T Configuration Manual Download Page 175

Page: 175 / 488

Chapter 4 Getting Started with Device Manager

175

System Configuration Guide

Table 29

describes the default access community strings for the Device Manager

software.

To display the device view:

Do one of the following:

•

Choose

Device > Open

•

Choose

Device > Open Last

, and select an IP address from the list.

•

Click the folder icon in the Device Manager window.

•

Press

Ctrl+O

The

Open Device

dialog box opens

(Figure 56)

Figure 56

Open Device dialog box

Table 29

SNMP community string default values

Access level

Description

Read-only

public

Read/write

private

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 175 / 488

Search results

Summary of Contents for 425-24T

Reviews: