Nortel 425-24T Configuration Manual Download Page 378

Page: 378 / 488

378

Chapter 11 Administering the switch using Web-based management

320985-A Rev 01

Figure 152

Quick Start page

Click on the

Submit

button after making the required settings.

Table 143

describes the items on the

Quick Start

page.

Table 143

Items on the Quick Start page

Section

Item

Description

In-Band Switch IP
Address

Specify a new IP address for the switch.

In-Band Subnet
Mask

Enter a new subnet mask.

Default Gateway

Specify an IP address for the default
gateway.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 378 / 488

Search results

Summary of Contents for 425-24T

Reviews: