manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 49 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 49

Chapter 1 About Ethernet Switches 325 and 425

49

System Configuration Guide

 

restore factory-default [-y]

where the 

[-y] 

parameter instructs the switch not to prompt for confirmation. 

For more information, refer to 

“Resetting the switch to default configuration” on 

page 261

.

Ping enhancement

Release 3.6 software extends the ping capabilities of the device. Using the CLI, 
you can now specify additional ping parameters, including the number of ICMP 
packets to be sent, the packet size, the interval between packets, and the timeout. 
You can also set ping to continuous, or you can set a debug flag to obtain extra 
debug information.

For more information, see 

“Pinging” on page 259

.

show interfaces config command

The 

show interfaces config

 CLI command displays the current operational 

status of interfaces and provides supplementary information about the current port 
settings for Spanning Tree Protocol.

For more information, see 

“show interfaces config command” on page 284

.

Autosave enable/disable enhancement

Release 3.6 software extends the ability to set autosave enable/disable using the 
Console Interface (Configuration File > Autosave Configuration) and Web-based 
management (Configuration > Configuration File). 

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments