manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 284 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 284

284

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

Figure 105   

show interfaces command output

show interfaces config command

The 

show interfaces config 

command displays the current operational 

status of interfaces and provides supplementary information about the current port 
settings for Spanning Tree Protocol.

The syntax for the 

show interfaces config 

command is:

show interfaces [<portlist>] config 

The 

show interfaces config 

command is in the privExec command mode.

425-48T(config-if)#show interfaces

              Status                     Auto                      Flow

Port Trunk Admin   Oper Link LinkTrap Negotiation Speed    Duplex Control

---- ----- ------- ---- ---- -------- ----------- -------- ------ -------

1          Enable  Down Down Enabled  Enabled

2          Enable  Down Down Enabled  Enabled

3          Enable  Down Down Enabled  Enabled

4          Enable  Down Down Enabled  Enabled

5          Enable  Down Down Enabled  Custom

6          Enable  Down Down Enabled  Enabled

7          Enable  Down Down Enabled  Enabled

8          Enable  Down Down Enabled  Enabled

9          Enable  Down Down Enabled  Enabled

10         Enable  Down Down Enabled  Enabled

11         Enable  Down Down Enabled  Enabled

12         Enable  Down Down Enabled  Enabled

13         Enable  Down Down Enabled  Enabled

14         Enable  Down Down Enabled  Enabled

15         Enable  Down Down Enabled  Enabled

16         Enable  Down Down Enabled  Enabled

17         Enable  Down Down Enabled  Enabled

18         Enable  Down Down Enabled  Enabled

19         Enable  Down Down Enabled  Enabled

425-48T(config-if)#

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments