manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 116 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 116

116

Chapter 2 Using the console interface

320985-A Rev 01

 

The 

Rate Limiting Configuration 

screen allows you to limit the forwarding rate 

of broadcast and multicast packets at ingress.

Figure 25

 show sample rate limiting values for the two 

Rate Limiting 

Configuration 

screens.

To open the

 Rate Limiting Configuration

 screen:

➨

Choose

 Rate Limiting Configuration

 (or press 

l

) from the 

Switch 

Configuration Menu

 screen.

Note: 

All configuration settings that you make in the 

Rate Limiting 

Configuration

 screen are applied across the entire unit (if stacking in 

configured). You cannot set some ports in the unit to limit broadcast 
traffic with a value of X pps (Packets Per Second) and some other ports 
in the same unit to limit multicast traffic with a value of Y pps.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments