Nortel 425-24T Configuration Manual Download Page 312

Page: 312 / 488

312

Chapter 7 System configuration using the CLI

320985-A Rev 01

Figure 119

show lldp port tx-stats command output

Figure 120

displays the output from the

show lldp stats

command.

Figure 120

show lldp port tx-tlv command output

Configuring LEDs on the display panel

The

blink-leds

command allows you to configure the LEDs on the display

panel to identify the unit. The syntax of the

blink-leds

command is:

blink-leds <off> <stop> <unit>

The

blink-leds

command is in the enable mode.

425>show lldp port 1/1 tx-stats

-------------------------------------------------------------------------

lldp tx-stats

-------------------------------------------------------------------------

Port Frames

-------------------------------------------------------------------------

1/1 123

-------------------------------------------------------------------------

425>show lldp port 1/1 tx-tlv

------------------------------------------------------------------------

lldp port tlvs

------------------------------------------------------------------------

Port PortDesc SysName SysDesc SysCap MgmtAddr

------------------------------------------------------------------------

1/1 true true true true false

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 312 / 488

Search results

Summary of Contents for 425-24T

Reviews: