manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 440 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 440

440

Default settings

320985-A Rev 01

 

Bridge Priority

HEX: 0x0000 - 0xF000

Spanning Tree Switch Settings screen 
in MSTP mode (see 

Configuring VLANs, 
Spanning Tree, and 
MultiLink Trunking for Nortel 
Ethernet Switches 325 and 425, 
Software Release 3.6

(320986-A))

Bridge Priority

HEX: 0x0000 - 0xF000

Root Port

0

Root Path Cost

0

Maximum Age Time

20 seconds

Forward Delay

15 seconds

Bridge Forward Delay

15 seconds

Tx Hold Count

3

Hop Count (Max)

2000

Default Path Cost Type

•

32 bits in MSTP/RSTP 
mode

•

16 bits in legacy 
STP802.1d mode

•

Not supported in 
STP802.1d mode

Region Name

MAC address of the device

TELNET Access

Enabled

“TELNET/SNMP/Web Access 
Configuration screen” on page 234

SNMP Access

Enabled

Web Access

Enabled, Yes

Login Timeout

1 minute

Login Retries

3

Inactivity Timeout

15 minutes

Event Logging

All

Allowed Source IP Address

(10 user-configurable fields)

First field: 0.0.0.0
(no IP address assigned)

Remaining nine fields: 
255.255.255.255
(any address is allowed)

Allowed Source Mask

(10 user-configurable fields)

First field: 0.0.0.0 
(no IP address assigned)

Remaining nine fields: 
255.255.255.255
(any address is allowed)

Table 167   

Factory default settings (continued)

Field

Default setting

Appears in this CI screen

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments