manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 173 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 173

Chapter 4 Getting Started with Device Manager

173

System Configuration Guide

 

Figure 55   

Properties dialog box

2

Type information and select check boxes.

3

Click 

OK

.

Table 28

 describes the 

Properties

 dialog box fields.

Table 28   

Properties dialog box fields

Area

Field

Description

Polling

Status Interval

Interval at which status information is gathered (default is 20 
seconds). For a full stack, set this interval to 60 seconds.

(If Traps, Status 
Interval:)

Interval at which statistics and status information are gathered 
when traps are enabled. The default is 60.

Hotswap Detect every:  The interval at which Device Manager detects the module 

information. The default is 1 interval.

Enable

Enables (true) or disables (false) periodic polling of the device 
for updated status. If polling is disabled, the chassis status is 
updated only when you click Refresh on the Chassis tab.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments