Nortel 425-24T Configuration Manual Download Page 77

Page: 77 / 488

Chapter 1 About Ethernet Switches 325 and 425

System Configuration Guide

M
(MGBIC)

Duplex Mode

Green

This port has a good connection (fiber), and is configured
to full duplex.

Off

This port does not have a good connection (fiber), and
port is configured to half duplex.

T
(Copper)
10/100/
1000 Link

10/100/1000
Mb/s port speed
indicator

Green

This port has a good connection (copper - at 1000 Mbps).

Amber

This port has a good connection (copper - at 100 Mbps).

Amber/
Green

This port has a good connection (copper - at 10 Mbps).

Off

This port does not have a good connection.

A
(Activity)

Port activity

Green

Blinking

Indicates network activity for the corresponding port. A
high level of network activity can cause the LEDs to
appear to be on continuously.

Table 9

Ethernet Switch 425 LED descriptions (continued)

Label

Command
Status

Color

State

Meaning

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 77 / 488

Search results

Summary of Contents for 425-24T

Reviews: