manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 326 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 326

326

Chapter 8 Ethernet port management using the CLI

320985-A Rev 01

 

default duplex command

The 

default

 

duplex

 command sets the duplex operation for a port to the 

factory default duplex value. The syntax for the 

default

 

duplex

 command is:

default duplex [port <portlist>]

The 

default

 

duplex

 command is in the config-if command mode.

Table 114

 describes the parameters and variables for the 

default

 

duplex

 

command. 

Enabling flow control

If you use a Gigabit Ethernet with the Ethernet Switch 425, you control traffic on 
this port using the 

flowcontrol

 command. This section covers the following 

commands:

•

“flowcontrol command” on page 327

•

“no flowcontrol command” on page 327

•

“default flowcontrol command” on page 328

Note: 

When you set the duplex mode for autonegotiation, ensure that 

the other side of the link is also set for autonegotiation.

Table 114   

default duplex command parameters and variables

Parameters and 
variables

Description

port <portlist>

Specifies the port numbers to reset the duplex mode to factory 
default values. Enter the port numbers you want to configure, or all 
to configure all ports simultaneously. The default value is 
autonegotiation.

Note:

 If you omit this parameter, the system uses the port number 

you specified in the 

interface

 command.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments