manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 332 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 332

332

Chapter 8 Ethernet port management using the CLI

320985-A Rev 01

 

The

 show auto-negotiation-advertisements 

command is in the 

userExec command mode.

Table 119

 describes the parameters and variables for the

 show 

auto-negotiation-advertisements

 

command. 

Figure 126

 displays sample output from the 

show 

auto-negotiation-advertisements 

command.

Figure 126   

show auto-negotiation-advertisements command output

show auto-negotiation-capabilities command

The

 show auto-negotiation-capabilities 

command displays the 

hardware advertisement capabilities for the switch. The syntax for the

 show 

auto-negotiation-capabilities 

command is:

show auto-negotiation-capabilities [port <portlist>]

The

 show auto-negotiation-capabilities 

command is in the userExec 

command mode.

Table 119   

show auto-negotiation-advertisements command

Parameters and values

Description

port <portlist>

Enter ports for which you want the current 
autonegotiation advertisements displayed.

425-48T(config-if)#show auto-negotiation-advertisements port 4,8,10

Port Autonegotiation Advertised Capabilities

---- ----------------------------------------------------------------

4    10Full

8    10Full

10   10Full

425-48T(config-if)#

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments