manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 242 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 242

242

Chapter 6 System configuration using the Console Interface

320985-A Rev 01

 

To open the

 Configuration File Download/Upload

 screen (

Figure 89

):

➨

Choose 

Configuration File Download/Upload 

(or press 

c

) from the main 

menu

Figure 89   

Configuration File Download/Upload screen

 

Table 54

 describes the 

Configuration File Download/Upload

 screen fields.

Table 54   

Configuration File Download/Upload screen fields

Field

Description

Configuration Image 
Filename

The file name you have chosen for the configuration file. Choose a 
meaningful file name that allows you to identify the file for retrieval when 
required. The file must already exist on your TFTP server and must be read/
write enabled.

Default value

Zero-length string

Range

An ASCII string of up to 30 printable characters

TFTP Server IP Address

The IP address of your TFTP load host.

Default value

0.0.0.0 (no IP address assigned)

Range

Four-octet dotted-decimal notation, where each octet is 
represented as a decimal value, separated by a decimal 
point

 Configuration File Download/Upload

     Configuration Image Filename:                [  ]

     TFTP Server IP Address:                      [ 198.202.188.174 ]

     Copy Configuration Image to Server:          [ No  ]

     Retrieve Configuration Image from Server:    [ No  ]

Enter text, press <Return> or <Enter> when complete.

Press Ctrl-R to return to previous menu. Press Ctrl-C to return to Main Menu.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments