manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 150 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 150

150

Chapter 4 Getting Started with Device Manager

320985-A Rev 01

 

Removing previous versions of JDM on Windows

Remove existing versions of Device Manager software by using the Uninstall DM 
option that was created in the Windows Start menu during installation.

For example, to remove Device Manager from a Windows XP system using the 
default program group, choose the following option from the Windows Start 
menu: All Programs>Nortel>Java Device Manager>Uninstall DM.

If no program group was added to the Windows Start menu during installation, 
then complete the following steps to remove existing Device Manager software: 

1

Navigate to the folder where the JDM software is installed.

2

Open the UninstallerData sub-folder.

3

Run the following file: 

Uninstall Java Device Manager.exe

.

Installing JDM on Windows from the CD

To access the JDM software from the installation CD:

1

Close all programs.

2

Insert the software CD into your CD-ROM drive.

3

From the Windows Start menu, choose 

Run

. 

The 

Run

 dialog box opens.

4

Use 

Browse

 to navigate to the drive where the CD-ROM is located.

Note: 

Removing previous versions of JDM is an optional process. Multiple 

versions of JDM can exist on one system, as long as each version is in a 
separate location.

If you decide to allow previous versions of JDM to remain, then you must 
choose a different folder to use during the installation process.

Note: 

If more than one version of Device Manager software is installed, 

ensure you select the correct software to uninstall.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments