manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 361 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 361

Chapter 9 Configuring the switch using Device Manager

361

System Configuration Guide

 

Figure 145   

File system - ASCII Config File dialog box

Table 136

 describes the 

ASCII Config File 

tab fields.

Table 136   

ASCII Config File tab fields

Field

Description

LoadServerAddr

The IP address of the load server for the ASCII configuration file. If not 
used, then the value is 0.0.0.0. 

ASCIIConfigFileName

Name of the ASCII configuration file currently associated with the 
interface. When not used, the value is a zero length string. 

ASCIIConfigAutoDownload

Specifies automatic ASCII configuration download.

ASCIIConfigAutodldStatus

Specifies the current status of the ASCII configuration file download.

ASCIIConfigManualDownload

Specifies manual download of an ASCII configuration file.

ASCIIConfigManualdldStatus

Specifies the current status of the manual download of an ASCII 
configuration file.

ASCIIConfigManualUpload

Specifies manual upload of an ASCII configuration file.

ASCIIConfigManualUpldStatus

Specifies the current status of the manual upload of an ASCII 
configuration file.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments