manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 394 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 394

394

Chapter 12 Configuring the switch using Web-based management

320985-A Rev 01

 

2

In the upper-left corner, click on the unit number for viewing the GBIC 
configuration.

Downloading switch images

You can download the Ethernet Switch 325/425 software image to non-volatile 
flash memory. To download the Ethernet Switch 325/425 software image, a 
properly configured Trivial File Transfer Protocol (TFTP) server must be present 
in your network, and the policy switch must have an IP address. To learn how to 
configure the switch or stack IP address, refer to 

“Configuring BootP, IP, and 

gateway settings” on page 385

.

To download a switch image:

1

From the main menu, choose 

Configuration > Software Download

. 

The 

Software Download 

page opens 

(Figure 162)

.

Figure 162   

Software Download page

Caution: 

Do not interrupt power to the device during the software 

download process. A power interruption can corrupt the firmware image.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments