manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 392 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 392

392

Chapter 12 Configuring the switch using Web-based management

320985-A Rev 01

 

2

In the upper-left corner, click on the unit number of the Ethernet Switch 425 
stack to manage.

The page is updated with the information for the selected switch.

3

In the port row of your choice, select from the lists.

4

Click 

Submit

.

Link

The current link state of the corresponding port as 
follows: 

Up: The port is connected and operational

Down: The port is not connected or is not operational.

Link Trap

(1) On
(2) Off

Choose to control whether link up/down traps are sent to 
the configured trap receiver from the switch.

The default setting is On.

Autonegotiation

(1) Enabled
(2) Disabled

Choose to enable or disable the autonegotiation feature. 

Choosing to enable autonegotiation sets the 
corresponding port speed to match the best service 
provided by the connected station, up to 100Mb/s in 
full-duplex mode. 

Note:

 Autonegotiation also enables auto sensing on 10/

100 ports.

The default setting is Enabled.

Speed / Duplex

(1) 10Mbs / Half
(2) 10Mbs / Full
(3) 100Mbs / Half
(4) 100Mbs / Full
(5) 1000Mbs / Full

Choose the Ethernet speed you want the port to 
support.

The default setting is 10 Mbs/Half when autonegotiation 
is disabled and 1000 Mb/s full-duplex for gigabit ports 
only.

Table 146   

Port Management page items 

 Item

Range

Description

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments