manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 365 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 365

Chapter 9 Configuring the switch using Device Manager

365

System Configuration Guide

 

Figure 147   

Diagnostics dialog box — Topology tab

 

Table 138

 describes the 

Topology

 tab fields.

Topology Table tab

To view more topology information:

1

From the Device Manager menu bar, choose 

Edit > Diagnostics

.

The 

Diagnostics

 dialog box opens with the 

Topology

 tab displayed

 

(Figure 147 on page 365)

.

2

Click the 

Topology Table

 tab. 

Table 138   

Topology tab fields

Field

Description

IpAddr

The IP address of the device.

Status

Whether Nortel topology is on (topOn) or off (topOff) for the 
device. The default value is topOn.

NmmLstChg

The value of sysUpTime the last time an entry in the network 
management MIB (NMM) topology table was added, deleted, or 
modified. If the table has not changed since the last cold or 
warm start of the agent.

NmmMaxNum

The maximum number of entries in the NMM topology table.

NmmCurNum

The current number of entries in the NMM topology table.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments