manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 311 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 311

Chapter 7 System configuration using the CLI

311

System Configuration Guide

 

Figure 117

 displays the output from the

 show lldp port 

neighbor-mgmt-addr 

command.

Figure 117   

show lldp port neighbor-mgmt-addr command output

Figure 118

 displays the output from the

 show lldp rx-stats 

command.

Figure 118   

show lldp port rx-stats command output

Figure 119

 displays the output from the

 show lldp tx-stats 

command.

425>show lldp port 1/1 neighbor-mgmt-addr

------------------------------------------------------------------------

                         lldp neighbor-mgmt-addr

------------------------------------------------------------------------

------------------------------------------------------------------------

Port   Time    Index ChassisIdSubtype     ChassisId

                     PortIdSubtype        PortId

MgmtAddr                         MgmtIfId MgmtAddrOID

------------------------------------------------------------------------

1/1   439194        5  MAC address        00:09:97:a2:9d:80

                       MAC address        00:09:97:a2:9d:98

ipV4  10.128.100.13                   0        1.3.6.1.4.1.45.3.57.2

------------------------------------------------------------------------

425>show lldp port 1/1 rx-stats

------------------------------------------------------------------------

                            lldp rx-stats

------------------------------------------------------------------------

------------------------------------------------------------------------

Port  Frames    Frames  Frames   TLVs      TLVs         AgeOuts

Num   Discarded Errors  Total    Discarded Unrecognized

------------------------------------------------------------------------

1/1              0       105         0         0         0

------------------------------------------------------------------------

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments