manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 110 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 110

110

Chapter 2 Using the console interface

320985-A Rev 01

 

Figure 22   

Port Configuration screen (1 of 2)

 Port Configuration

 Port   Trunk    Status      Link   LnkTrap  Autonegotiation   Speed  Duplex

 ----   -----  ------------  -----  -------  --------------- -----------------

   1           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

   2           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

   3           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

   4           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

   5           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

   6           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

   7           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

   8           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

   9           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

  10           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

  11           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

  12           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

  13           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

  14           [ Enabled  ]   Down  [ On  ]   [ Enabled  ]     [               ]

                                                                     More...

Press Ctrl-N to display next screen.

Use space bar to display choices, press <Return> or <Enter> to select choice.

Press Ctrl-R to return to previous menu.  Press Ctrl-C to return to Main Menu.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments