manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 35 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 35

Preface

35

System Configuration Guide

 

Related publications

For more information about using the Ethernet Switch 325/425, refer to the 
following publications:

•

Release Notes for the Nortel Ethernet Switch 325/425, Software Release 3.6 

(217155-C)

Documents important changes about the software and hardware that are not 
covered in other related publications.

•

Configuring VLANs, Spanning Tree, and MultiLink Trunking for Nortel 
Ethernet Switches 325 and 425, Software Release 3.6

(320986-A)

Describes how to configure Virtual Local Area Networks (VLAN), Spanning 
Tree Protocol (STP), and MultiLink Trunk (MLT) features for the Nortel 
Ethernet Switches 325 and 425.

italic text

Indicates variables in command syntax descriptions. 
Also indicates new terms and book titles. Where a 
variable is two or more words, the words are connected 
by an underscore.
Example: If the command syntax is

show at

 

<valid_route>

, 

valid_route

is one variable and you substitute one 

value for it.

plain Courier 
text

Indicates command syntax and system output, for 
example, prompts and system messages.
Example: 

Set Trap Monitor Filters

separator ( > )

Shows menu paths. 
Example: 

Protocols > IP

 identifies the 

IP

 command on 

the 

Protocols

 menu. 

vertical line ( 

|

 )

Separates choices for command keywords and 
arguments. Enter only one of the choices. Do not type 
the vertical line when entering the command.
Example: If the command syntax is

show ip

 

{alerts|routes}

, you enter either

show ip alerts

 or 

show ip routes

, but not

both.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments