manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 362 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 362

362

Chapter 9 Configuring the switch using Device Manager

320985-A Rev 01

 

Working with SNTP

The Simple Network Time Protocol (SNTP) feature synchronizes the Universal 
Coordinated Time (UTC) to an accuracy within 1 second. This feature adheres to 
the IEEE RFC 2030 (MIB is the s5agent). With this feature, the system can obtain 
the time from any RFC 2030-compliant NTP/SNTP server.

The system retries connecting with the NTP server a maximum of 3 times, with 5 
minutes between each retry. If the connection fails after the 3 attempts, the system 
waits for the next synchronization time (the default is 24 hours) and begins the 
process again.

Configuring SNTP

The 

SNTP

 dialog box contains the parameters for configuring Simple Network 

Time Protocol (SNTP).

To open the 

SNTP

 dialog box:

1

From the Main Menu, choose 

Edit > SNTP

.

The 

SNTP

 dialog box opens 

(Figure 146)

.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments