manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 410 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 410

410

Installing an SFP Transceiver

320985-A Rev 01

 

Guidelines

Before installing an SFP, read the following guidelines:

•

SFP GBICs are static sensitive.

To prevent damage from ElectroStatic Discharge (ESD), follow your normal 
board and component handling procedures.

•

SFP GBICs, are dust sensitive. 

When you store an SFP GBIC, or when you disconnect it from a fiber optic 
cable, always keep the dust cover over the SFP GBIC optical bore.

•

To clean contaminants from the optical bores of a SFP GBIC, use an alcohol 
swab or equivalent to clean the ferrules of the optical connector.

•

Dispose this product (if necessary) according to all national laws and 
regulations.

Product Description

This section describes the SFP and label, and provides a model list for 
1000BASE-SX, 1000BASE-LX SFPs.

This section also describes the Nortel Coarse Wavelength Division Multiplexed 
(CWDM) SFPs and provides a CWDM SFP model list.

This section includes the following topics:

•

“Locking/extractor mechanisms” on page 411

•

“SFP labeling” on page 411

•

“SFP models” on page 412

•

“CWDM SFP models” on page 413

Warning: 

Fiber optic equipment can emit laser or infrared light that can 

injure your eyes. Never look into an optical fiber or connector port. 
Always assume that fiber optic cables are connected to a light source.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments