manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 309 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 309

Chapter 7 System configuration using the CLI

309

System Configuration Guide

 

Figure 114

 displays the output from the

 show lldp mgmt-sys-data 

command.

Figure 114   

show lldp mgmt-sys-data command output

Figure 115

 displays the output from the

 show lldp stats 

command.

Figure 115   

show lldp stats command output

show lldp port command

The 

show lldp port 

command displays configuration data for LLDP ports. 

The syntax for the 

show lldp port 

command is:

show lldp [port 

<portlist>

]

 

[neighbor] [neighbor-mgmt-addr] 

[rx-stats] [tx-stats] [tx-tlv]

The 

show lldp port

 

command is in the exec command mode. 

425>show lldp mgmt-sys-data

-------------------------------------------------------------------------

                             lldp mgmt-sys-data

-------------------------------------------------------------------------

-------------------------------------------------------------------------

MgmtAddr                          MgmtIfId    MgmtAddrOID

-------------------------------------------------------------------------

ipV4  10.128.100.100                0         1.3.6.1.4.1.45.3.57.1

-------------------------------------------------------------------------

425>show lldp stats

-------------------------------------------------------------------------

                          lldp stats

-------------------------------------------------------------------------

-------------------------------------------------------------------------

LastChange    RemTable RemTable RemTable RemTable

Time          Inserts  Deletes  Drops    Ageouts

-------------------------------------------------------------------------

00:01:18.00    1         0         0         0

-------------------------------------------------------------------------

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments