manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 286 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 286

286

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

copy config nvram

The 

copy config nvram

 command is in the privExec command mode.

The 

copy config nvram

 command has no parameters or variables.

write memory command

The 

write memory 

command copies the current configuration to NVRAM. The 

syntax for the 

write memory

 command is:

write memory

The 

write memory

 command is in the privExec command mode.

The 

write memory

 command has no parameters or variables.

save config command

The 

save config

 command copies the current configuration to NVRAM. The 

syntax for the 

save config

 command is:

save config

The 

save config

 command is in the privExec command mode.

The 

save config

 command has no parameters or variables.

Note: 

The system automatically issues the 

copy config nvram

 

command periodically. See 

“Enabling and disabling autosave” on 

page 287

 for details.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments