manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 228 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 228

228

Chapter 6 System configuration using the Console Interface

320985-A Rev 01

 

Console Read-Only 
Stack Password

When the Console Switch Password field is set to Required (for Telnet, for 
Console, or for Both), this field allows read-only password access to the CI of 

any participating switch in a stack configuration

. Users can access the CI using 

the correct password (see default), but cannot change any parameters or use 
the Reset option or Reset to Default option.

Default Value

user

Range

An ASCII string of up to 15 printable characters

Table 50   

Console/Comm Port Configuration screen fields (continued)

Field

Description

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments