Nortel 425-24T Configuration Manual Download Page 305

Page: 305 / 488

Chapter 7 System configuration using the CLI

305

System Configuration Guide

default lldp tx-tlv command

The

default lldp tx-tlv

command specifies the optional TLVs not to

include in the transmitted LLDPDUs (by default, the optional TLVs are not
included in LLDPDUs). The syntax for the

default lldp tx-tlv

command

is:

default lldp tx-tlv [port <portlist>] [port-desc] [sys-name]

[sys-desc] [sys-cap] [local-mgmt-addr]

The

default lldp tx-tlv

command is in the config-if command mode.

Table 97

describes the parameters and variables for the

default lldp tx-tlv

command.

lldp port status command

The

lldp port status

command sets the LLDPU transmit and receive status

on ports. The syntax for the

lldp port status

command is:

lldp port

<portlist>

status [rxOnly | txAndRx | txOnly]

The

lldp port status

command is in the config-if command mode.

Table 98

default lldp tx-tlv command parameters and variables

Parameters and
variables

Description

port

<portlist>

Specifies the ports affected by the command.

port-desc

Port description TLV. (default value is false: not included)

sys-name

System name TLV (default value is false: not included)

sys-desc

System description TLV (default value is false: not included)

sys-cap

System capabilities TLV (default value is false: not included)

local-mgmt-addr

Local management address TLV (default value is false: not
included)

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 305 / 488

Search results

Summary of Contents for 425-24T

Reviews: