Nortel 425-24T Configuration Manual Download Page 471

Page: 471 / 488

Technical specifications

471

System Configuration Guide

Performance specifications

Table 173

lists performance specifications for the Ethernet Switch 325.

Table 174

lists performance specifications for the Ethernet Switch 425.

Data rate

The data rate is 10 Mb/s Manchester encoded or 100 Mb/s 4B/5B encoded.

Table 173

Performance specifications of the Ethernet Switch 325

Parameter

Specifications

Frame Forward Rate
(64-byte packets)

3.6 Million packets per second (Mpps) for the Ethernet
Switch 325-24T, and 6.6 Mpps for the Ethernet Switch
325-24G.

Port Forwarding/Filtering
Performance
(64-byte packets)

•

For 10 Mb/s: 14,880 pps maximum

•

For 100 Mb/s: 148,810 pps maximum

Address Database Size

8,000 entries at line rate

Addressing

48-bit MAC address

Frame Length

64 to 1518 bytes (IEEE 802.1Q Untagged)

68 to 1522 bytes (IEEE 802.1Q Tagged)

Table 174

Performance specifications of the Ethernet Switch 425

Parameter

Specifications

Frame Forward Rate
(64-byte packets)

Up to 3.2 million packets per second (pps) maximum,
learned unicast traffic; 5.1 million packets per second (pps)
in a stack configuration

Port Forwarding/Filtering
Performance
(64-byte packets)

•

For 10 Mb/s: 14,880 pps maximum

•

For 100 Mb/s: 148,810 pps maximum

Address Database Size

8,000 entries at line rate

Addressing

48-bit MAC address

Frame Length

64 to 1518 bytes (IEEE 802.1Q Untagged)

68 to 1522 bytes (IEEE 802.1Q Tagged)

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 471 / 488

Search results

Summary of Contents for 425-24T

Reviews: