manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 255 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 255

Chapter 7 System configuration using the CLI

255

System Configuration Guide

 

The 

no ip default-gateway

 

command has no parameters or variables.

show ip command

The 

show

 

ip

 

command displays the IP configurations, specifically BootP mode, 

stack address, switch address, subnet mask, and gateway address. This command 
displays the these parameters for what is configured, what is in use, and the last 
BootP. The syntax for the 

show ip

 command is:

show ip [bootp] [default-gateway] [address [stack|switch]] 

[dns]

The 

show

 

ip

 

command is in the exec command mode. 

If you do not enter any parameters, this command displays all the IP-related 
configuration information. 

Table 61

 describes the parameters and variables for the 

show ip

 

command. 

Figure 92

 displays a sample output of the 

show ip

 command.

Note: 

When you change the IP gateway address, you may lose 

connection to Telnet and the Web. You also may disable any new Telnet 
connection required to connect to the serial console port to configure a 
new IP Gateway address.

Table 61   

show ip command parameters and variables

Parameters and 
variables

Description

bootp

Displays BootP-related IP information.

 

default-gateway

Displays the IP address of the default gateway. 

address

Displays the current IP address.

 

stack|switch

Specifies current IP address of the stack or the switch.

dns

Displays DNS configuration.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments