manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 412 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 412

412

Installing an SFP Transceiver

320985-A Rev 01

 

Figure 168   

Nortel SFP label

SFP models

SFPs are hot-swappable input/output enhancement components designed for use 
with Nortel products to allow Gigabit Ethernet ports to link with other Gigabit 
Ethernet ports over various media types. 

Table 156

 lists and describes the Nortel 

SFP models that are supported by the Ethernet Switch 425.

Table 156   

1000BASE-SFP models

Model number

Product Number

Description

1000Base-SX SFP GBIC 
(mini-GBIC, connector type: 
LC).

AA1419013

Small Form Factor 
Pluggable, short wavelength 
550 m

1-port 1000Base-SX SFP 
GBIC (mini-GBIC, connector 
type: MT-RJ).

AA1419014

Small Form Factor 
Pluggable, short wavelength 
550 m

 1-port 1000Base-LX SFP 
GBIC (mini-GBIC, connector 
type: LC). 

AA1419015

Small Form Factor 
Pluggable, long wavelength 
5 km

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments