manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 374 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 374

374

Chapter 10 Configuring ports using Device Manager

320985-A Rev 01

 

AutoNegotiation
Capability

Specifies the port speed and duplex capabilities that a switch can 
support on a port, and that may be advertised by the port using 
auto-negotiation

AutoNegotiation
Advertisments

Specifies the port speed and duplex abilities to be advertised during 
link negotiation.

MltId

The MultiLink Trunk to which the port is assigned (if any).

IsPortShared

Specifies whether a port is shared. Multiple ports that are logically 
represented as a single port are shared. Only one shared port may be 
active at a time.

PortActiveComp
onent

Specifies the physical port components that are active for a shared 
port.

Table 141   

Interface tab fields for multiple ports (continued)

Field

Description

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments