manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 143 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 143

Chapter 3 CLI Basics

143

System Configuration Guide

 

Figure 35

 displays sample output from the 

show stacking-mode

 

command.

Figure 35   

show stacking-mode command output

renumber unit command

This command is applicable only to Ethernet Switch 425-24T, in its stacked 
mode.

The 

renumber unit

 command changes the unit number of each switch in the 

stack. The syntax for the 

renumber unit

 

command is:

renumber unit

The 

renumber unit

 command is in the config command mode.

The 

renumber unit

 

command has no parameters or variables.

Managing MAC address forwarding database table

This section describes the commands to view the contents of the MAC address 
forwarding database table, as well as setting the age-out time for the addresses. 
The following topics are covered:

•

“show mac-address-table command” on page 144

•

“mac-address-table aging-time command” on page 145

•

“default mac-address-table aging-time command” on page 146

Note: 

This command does not take effect until you reset the stack.

425-24T>show stacking-mode

Current mode for unit 1 is stackable, base unit set.

Next mode for unit 1 is stackable, base unit set.

Current mode for unit 2 is stackable, base unit not set.

Next mode for unit 3 is stackable, base unit not set.

Next mode will be applied after reset

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments