manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 146 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 146

146

Chapter 3 CLI Basics

320985-A Rev 01

 

Figure 37

 displays sample output from the 

mac-address-table aging-time 

command.

Figure 37   

mac-address-table aging-time output

default mac-address-table aging-time command

The 

default

 

mac-address-table aging-time

 command sets the time that 

the switch retains unseen MAC addresses to 300 seconds. The syntax for the 

default

 

mac-address-table aging-time

 command is:

default mac-address aging-time 

The 

default

 

mac-address-table aging-time

 command is in the config 

command mode.

The 

default

 

mac-address-table aging-time

 command has no parameters 

or variables.

425-48T(config)#mac-address-table aging-time 400

425-48T(config)#

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments