manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 367 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 367

367

System Configuration Guide

 

Chapter 10
Configuring ports using Device Manager

This chapter describes how to use Device Manager to configure ports on an 
Ethernet Switch 325/425.

The windows displayed when you configure a single port differ from the ones 
displayed when you configure multiple ports. However, the options are similar. 

This section covers:

•

“Viewing and editing a single port configuration”

•

“Viewing and editing multiple port configurations” on page 371

Viewing and editing a single port configuration

To view or edit the configuration of a single port:

➨

Do one of the following:

•

Double-click on a single port.

•

From the Device Manager main menu, choose 

Edit > Port.

•

From the shortcut menu, choose 

Edit

.

•

From the toolbar, click 

Edit

.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments