Nortel 425-24T Configuration Manual Download Page 343

Page: 343 / 488

Chapter 9 Configuring the switch using Device Manager

343

System Configuration Guide

Editing the chassis configuration

You can edit a chassis configuration from the

Edit Chassis

dialog box.

To open the

Chassis

dialog box:

Select the chassis.

Do one of the following:

•

From the Device Manager main menu, choose

Edit > Chassis.

•

On the toolbar, click

Edit

The following sections provide a description of the tabs in the

Edit > Chassis

dialog box and details about each field on the tab.

System tab

You can use the

System

tab to specify tracking information for a device, device

descriptions, and so on.

To open the

System

tab:

Select the chassis.

From the shortcut menu, choose

Edit > Chassis

The

Chassis

dialog box opens with the

System

tab displayed

(Figure 133)

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 343 / 488

Search results

Summary of Contents for 425-24T

Reviews: