manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 71 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 71

Chapter 1 About Ethernet Switches 325 and 425

71

System Configuration Guide

 

3

To confirm, keep the UI button pressed for 3 seconds more. The UI LED turns 
either to solid-green (command accepted) or to solid-amber (error). After 
another period (5 seconds) the UI LED turns Off.

Once the command is accepted, the new configuration is stored in NVRAM.

Table 7

 describes the LED indications associated with the UI button.

Table 7   

UI button LEDs on the Ethernet Switch 425-24T

Note: 

When resetting the unit using the UI button, wait 60 seconds after 

your last configuration change. The system takes up to 60 seconds to 
save configuration changes to NVRAM. You can reset the stack 
immediately after changing the configuration using the UI button 
without losing any of the changed configuration.

Label

Color/Status

Description

UI

Green/blinking

The user pushed the UI button and activated 
the front-panel configuration mode; the 
system is awaiting input.

Green/steady

The system accepts the UI button input.

Amber/blinking

The system rejected the UI button input.

Pwr

Green

Power on.

Amber/slow blinking

The system will reset in < 3 seconds. To stop 
reset, release UI button.

Amber/fast blinking

The system will reset in < 1 second. To stop 
reset, release UI button.

Base

Green/steady

The unit is the base unit for the stack.

Green/blinking

The unit is in configuration mode using the UI 
button. The UI LED is also blinking green.

Amber

The stack is reset using the UI button.

Off

The switch is not the stack base unit, or it is 
operating in standalone mode.

Up

Green/steady

The unit is being set as base or non-base unit 
using the UI button—base unit has Base LED 
on as well.

Amber/blinking

The stack is reset using the UI button.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments