manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 80 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 80

80

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

 

United Kingdom:

•

BS1363 male plug with fuse 

•

Harmonized cord 

240 VAC 
50 Hz 
Single phase

Australia:

AS3112-1981 Male plug

240 VAC 
50 Hz 
Single phase

Caution: Please read immediately.

Inspect this power cord and determine if it provides the proper plug and is 
appropriately certified for use with your electrical system. Immediately discard this 
cord if it is inappropriate for your country's electrical system and obtain the proper 
cord as required by your national electrical codes or ordinances.

Refer to this product's technical documentation for detailed installation procedures to 
be followed by qualified service personnel.

Table 11   

International power cord specifications (continued)

Country/Plug description

Specifications

Typical plug

229FA

230FA

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments