manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 139 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 139

Chapter 3 CLI Basics

139

System Configuration Guide

 

show tech command

The 

show tech 

command displays the system information. The syntax for the 

show tech 

command is:

show tech

The 

show tech 

command is in the privExec command mode. The 

show tech 

command has no parameters or variables.

Figure 31

, 

Figure 31 on page 139

, and 

Figure 32 on page 140

 display a sample 

output from the 

show tech

 

command.

Figure 31   

show tech command output

425# show tech

*****SYS Info*****

System Information:

        Operation Mode:       Switch

        MAC Address:          00-09-97-A2-9D-80

        Reset Count:          123

        Last Reset Type:      Management Reset

        Autotopology:         Enabled

        sysObjectID:          1.3.6.1.4.1.45.3.57.2

        sysUpTime:            2 days, 04:41:28

        sysNtpTime:           SNTP not synchronized.

        sysServices:          3

        sysContact:

        sysName:              425

        sysLocation:

Unit #1:

        Switch Model:         425-24T

        MDA Model:            None

        Cascade Module:       400-ST1

        Hardware Version:     0B

        Firmware Version:     3.5.0.2

        Software Version:     v3.6.0

        Serial Number:        SACC25003U

        Manufacturing Date:   05232003

        Power Status:         Primary

        Fan #1 Status:        Normal

        Fan #2 Status:        Normal

*****UI Button*****

 Unit #  Button Mode

 ------  -------------

 1        Enabled

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments