manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 333 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 333

Chapter 8 Ethernet port management using the CLI

333

System Configuration Guide

 

Table 120

 describes the parameters and variables for the

 show 

auto-negotiation-capabilities

 

command. 

Figure 127

 displays sample output from the 

show 

auto-negotiation-capabilities 

command.

Figure 127   

show auto-negotiation-capabilities command output

auto-negotiation-advertisements command

The

 auto-negotiation-advertisements 

command configures 

advertisements for the switch. The syntax for the

 

auto-negotiation-advertisements 

command is:

auto-negotiation-advertisements [port <portlist>] [10-full] 

[10-half] [100-full] [100-half] [1000-full] [1000-half] 

[asymm-pause-frame] [pause-frame] [none]

The

 auto-negotiation-advertisements 

command is in the interface 

configuration command mode.

Table 120   

show auto-negotiation-capabilities command

Parameters and values

Description

port <portlist>

Enter ports for which you want the autonegotiation 
capabilities displayed.

425-48T(config-if)#show auto-negotiation-capabilities port 5,6,10

Port Autonegotiation Capabilities

---- ----------------------------------------------------------------

5    10Full 10Half 100Full 100Half

6    10Full 10Half 100Full 100Half

10   10Full 10Half 100Full 100Half

425-48T(config-if)#

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments