Nortel 425-24T Configuration Manual Download Page 291

Page: 291 / 488

Chapter 7 System configuration using the CLI

291

System Configuration Guide

sntp server primary address command

The

sntp server primary address

command specifies the IP addresses of

the primary NTP server. The syntax for the

sntp server primary address

command is:

sntp server primary address

A.B.C.D>

The

sntp server primary address

command is in the config command

mode.

Table 85

describes the parameters and variables for the

sntp server primary

address

command.

The default is 0.0.0.0.

sntp server secondary address command

The

sntp server secondary address

command specifies the IP addresses

of the secondary NTP server. The syntax for the

sntp server secondary

address

command is:

sntp server secondary address

A.B.C.D>

The

sntp server secondary address

command is in the config command

mode.

Table 85

sntp server primary address command parameters and variables

Parameters and
variables

Description

<A.B.C.D>

Enter the IP address of the primary NTP server.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 291 / 488

Search results

Summary of Contents for 425-24T

Reviews: