manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 36 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 36

36

Preface

320985-A Rev 01

 

•

Configuring QoS for Nortel Ethernet Switches 325 and 425, Software 
Release 3.6

(320987-A)

Describes how to configure and manage Quality of Service and IP Filtering 
features for the Nortel Ethernet Switches 325 and 425.

•

Configuring and Managing Security for Nortel Ethernet Switches 
325 and 425, Software Release 3.6

(320988-A)

Describes how to configure and manage security for the Nortel Ethernet 
Switches 325 and 425.

•

System Monitoring Guide for Nortel Ethernet Switches 325 and 425, Software 
Release 3.6

(320989-A)

Describes how to configure system logging and network monitoring, and how 
to display system statistics for the Nortel Ethernet Switches 325 and 425.

•

Configuring IP Multicast for Nortel Ethernet Switches 325 and 425, Software 
Release 3.6

(320990-A)

Describes how to configure IP Multicast Routing Protocol features for the 
Nortel Ethernet Switches 325 and 425.

You can print selected technical manuals and release notes free, directly from 
Internet. Go to 

www.nortel.com/support

. Find the product for which you need 

documentation. Then locate the specific category and model or version for your 
hardware or software product. Use Adobe* Reader* to open the manuals and 
release notes, search for the sections you need, and print them on most standard 
printers. Go to 

www.adobe.com

 to download a free copy of Adobe Reader.

How to get help

This section explains how to get help for Nortel products and services.

Getting help from the Nortel web site

The best way to get technical support for Nortel products is from the Nortel 
Technical Support web site:

www.nortel.com/support

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments