Nortel 425-24T Configuration Manual Download Page 211

Page: 211 / 488

Chapter 5 Using the Web-based management interface

211

System Configuration Guide

Identifying unit numbers

You can identify unit numbers of the switches participating in a stack
configuration by viewing the active LEDs on the front panel of each switch.

To identify unit numbers in your configuration:

From the main menu, choose

Summary > Identify Unit Numbers

The

Identify Unit Numbers

page opens

(Figure 78)

Figure 78

Identify Unit Numbers page

To continue viewing summary information or to start the configuration
process, choose another option from the main menu.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 211 / 488

Search results

Summary of Contents for 425-24T

Reviews: