Nortel 425-24T Configuration Manual Download Page 214

Page: 214 / 488

214

Chapter 6 System configuration using the Console Interface

320985-A Rev 01

IP Configuration/Setup screen

The

IP Configuration/Setup

screen (

Figure 79

) allows you to set or modify the

Ethernet Switch 325/425 IP configuration parameters. Data that you enter in the
user-configurable fields takes effect as soon as you press

Enter

To open the

IP Configuration/Setup

screen:

Figure 79

IP Configuration/Setup screen

Table 47

describes the

IP Configuration/Setup

screen fields.

➨

Choose

IP Configuration/Setup

(or press

) from the main menu.

Note:

The read-only fields in this screen are updated based on the BootP

mode specified in the BootP Request Mode field. (See

“Choosing a

BootP request mode” on page 216

for more information.)

IP Configuration/Setup

BootP Request Mode: [ BootP When Needed ]

Configurable In Use Last BootP

------------------- --------------- -------------

In-Band Stack IP Address: [ 0.0.0.0 ] 0.0.0.0 0.0.0.0

In-Band Switch IP Address: [ 134.177.224.102 ] 134.177.224.102 0.0.0.0

In-Band Subnet Mask: [ 255.255.255.0 ] 255.255.255.0 0.0.0.0

Default Gateway: [ 134.177.224.1 ] 134.177.224.1 0.0.0.0

IP Address to Ping: [ 10.30.40.1 ]

Start Ping: [ No ]

Use space bar to display choices, press <Return> or <Enter> to select choice.

Press Ctrl-R to return to previous menu. Press Ctrl-C to return to Main Menu.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 214 / 488

Search results

Summary of Contents for 425-24T

Reviews: