manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 104 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 104

104

Chapter 2 Using the console interface

320985-A Rev 01

 

Table 16

 describes the 

Switch Configuration Menu

 options. 

Table 16   

Switch Configuration Menu options

Option

Description

MAC Address Table

Displays the 

MAC Address Table

 screen (see 

Configuring and 

Managing Security for Nortel Ethernet Switches 325 and 425, 
Software Release 3.6

(320988-A)). This screen allows you to view 

all MAC addresses and their associated port or trunk that the switch 
has learned, or to search for a particular MAC address (to see if the 
switch has learned the address).

MAC Address Security 
Configuration...

Displays the 

MAC Address Security Configuration

 

Menu

 (see 

Configuring and Managing Security for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320988-A)). This screen allows you to set up the MAC 

address security feature and provides the following options: MAC 
Address Security Configuration, MAC Address Security Port 
Configuration, MAC Address Security Port Lists, and MAC Address 
Security Table. This menu allows you to enable and disable security 
features on the port and trunk levels.

EAPoL Security Configuration

Displays the 

EAPOL Security Configuration Menu 

(see 

“

Configuring and Managing Security for Nortel 

Ethernet Switches 325 and 425, Software 
Release 3.6

(320988-A)”). This screen allows you to set up 

Extensible Authentication Protocol over LAN (EAPOL)- based 
security.

VLAN Configuration...

Displays the 

VLAN Configuration Menu 

(see 

Configuring VLANs, 

Spanning Tree, and MultiLink Trunking for Nortel 
Ethernet Switches 325 and 425, Software 
Release 3.6

(320986-A)). This menu provides the following options: 

VLAN Configuration, VLAN Port Configuration, VLAN Display by Port, 
MAC-SA, and Return to Switch Configuration Menu screen. This 
menu allows you to create and modify VLANs.

Port Configuration...

Displays the 

Port Configuration 

screen (see 

“Port Configuration 

screen” on page 109

). This screen allows you to configure a specific 

switch port, all switch ports or, when in a stack configuration, all stack 
ports.

High Speed Flow Control 
Configuration...

Displays the 

High Speed Flow Control Configuration 

screen. (see 

“High Speed Flow Control Configuration screen” on page 112

).

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments