manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 149 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 149

Chapter 4 Getting Started with Device Manager

149

System Configuration Guide

 

Installing the Device Manager software

Device Manager software can be installed in Windows, UNIX, or Linux 
environment. The following sections provide information on the system 
requirements and installation procedures to install Device Manager software in 
Windows, UNIX, and Linux environments.

•

“Installing JDM on Windows”

•

“Installing JDM on UNIX or Linux” on page 159

Installing JDM on Windows

This section includes the following topics:

•

“Windows minimum requirements”

•

“Removing previous versions of JDM on Windows” on page 150

•

“Installing JDM on Windows from the CD” on page 150

•

“Installing JDM on Windows from the web” on page 151

•

“Executing the JDM installation software on Windows” on page 152

Windows minimum requirements

The minimum system requirements for installing JDM on Microsoft*

 

Windows NT*, Windows

 

95, Windows 98, Windows 2000, or Windows XP are:

•

350 MHz or higher Pentium processor 

•

256 MB DRAM

•

300 MB space on hard drive

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments