manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 307 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 307

Chapter 7 System configuration using the CLI

307

System Configuration Guide

 

The 

default lldp port status

 

command is in the config-if command 

mode. 

Table 101

 describes the parameters and variables for the 

default lldp port 

status

 

command. 

show lldp command

The 

show lldp 

command displays configuration data for LLDP. The syntax for 

the 

show lldp

 command is:

show lldp [local-sys-data] [mgmt-sys-data] [stats]

The 

show lldp

 

command is in the exec command mode. 

Table 102

 describes the parameters and variables for the 

show lldp

 

command. 

Table 101   

default lldp port status command parameters and variables

Parameters and 
variables

Description

port 

<portlist>

Specifies the ports affected by the command.

Table 102   

show lldp command parameters and variables

Parameters and 
variables

Description

local-sys-data

Displays local LLDP system data.

mgmt-sys-data

Displays LLDP management data.

stats

Displays LLDP statistics. 

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments