manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 433 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 433

Default settings

433

System Configuration Guide

 

Aging Time

300 seconds

MAC Address Table screen (see 

Configuring and Managing 
Security for Nortel 
Ethernet Switches 325 and 425, 
Software Release 3.6

(320988-A))

Find an Address

00-00-00-00-00-00 
(no MAC address assigned)

MAC Address Security

Disabled

MAC Address Security Configuration 
Menu screen (see 

Configuring and 

Managing Security for Nortel 
Ethernet Switches 325 and 425, 
Software Release 3.6

(320988-A))

MAC Address Security 
SNMP-Locked

Disabled

Partition Port on Intrusion 
Detected

Disabled

Partition Time

0 seconds (the value 0 
indicates forever)

DA Filtering on Intrusion Detected

Disabled

Generate SNMP Trap on Intrusion

Disabled

Clear by Ports

NONE

Learn by Ports

NONE

Current Learning Mode

Not Learning

Trunk

blank field

MAC Address Security Port 
Configuration screen (see 

Configuring and Managing 
Security for Nortel 
Ethernet Switches 325 and 425, 
Software Release 3.6

(320988-A))

Security

Disabled

Port List

Blank field

MAC Address Security Port Lists 
screens (see 

Configuring and 

Managing Security for Nortel 
Ethernet Switches 325 and 425, 
Software Release 3.6

(320988-A))

Find an Address

Blank field

MAC Address Security Table screens 
(see 

Configuring and Managing 

Security for Nortel 
Ethernet Switches 325 and 425, 
Software Release 3.6

(320988-A))

MAC Address

Blank field (no address 
assigned)

Allowed Source 

Blank field

Display/Create MAC Address

00-00-00-00-00-00

Table 167   

Factory default settings (continued)

Field

Default setting

Appears in this CI screen

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments