manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 170 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 170

170

Chapter 4 Getting Started with Device Manager

320985-A Rev 01

 

When the installation is complete, the 

Install Complete

 dialog box opens 

(

Figure 53

).

Figure 53   

Install Complete dialog box

12

Click 

Done

 to exit the installation.

JDM is now installed on your machine. 

Removing JDM in Unix or Linux environments

In a UNIX or Linux environment, complete the following steps to remove the 
existing JDM software:

1

Navigate to the directory where the JDM software is installed (for example 

/JDM

).

2

Open the UninstallerData sub-directory.

3

Run the following file: 

Uninstall_Java_Device_Manager

.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments